Model D, Original
Parts listed here are compatible with Model Ds manufactured from July 14, 2003–July 21, 2006 (serial numbers 071403–072106).

Model D, Original There are 114 products.

per page
Showing 51 - 75 of 114 items
  • $2.20

    For use with Model C, D and E Indoor Rowers. This is a 3-3/8 inch diameter pulley that the shock cord (part number 1731) runs over inside the Concept2 Indoor Rower. There are four per machine. Sold individually. See more info.

    $2.20
  • $2.00

    For use on the front legs of Model C, D (original and updated) and E Indoor Rowers, this is a bag of eight patched fasteners. If you need to replace missing fasteners on the front leg of your indoor rower, this is what you need. Important: For use only on the front leg of Models C, D, and E Indoor Rowers; not intended for use in other areas of the...

    $2.00
  • $1.85

    For use on all Model C, D and E Indoor Rowers. This is the 17mm bearing located outside of the flywheel. The corresponding bearing cup (part number 1012) is sold separately. See more info.

    $1.85
  • $1.70

    For use on all Model B, C, D, E and Dynamic Indoor Rowers. This is the R8 bearing located outside of the flywheel. The corresponding bearing cup (part number 1013 or 258 depending on which model you have) is sold separately. See more info.

    $1.70
  • $1.50

    For use on all Model C, D, E, and Dynamic Indoor Rowers and the SkiErg. Using this knob instead of a nut makes it easier to take the monitor on and off of the equipment.

    $1.50
  • $1.50

    For use on the Model C, D and E Indoor Rower. 

    $1.50
  • $1.50

    For use on the Model C, D and E Indoor Rower. This is the end cap for the front of the indoor rower. See more info.

    $1.50
  • $1.50

    For use with Model A, B, C, D, E and Dynamic Indoor Rowers. This is the hard plastic cap that goes on the rear and/or front metal legs of the indoor rower to protect your carpet or floor and keep the machine from sliding back and forth while you row. Two to four per machine, depending on age and indoor rower model. Sold individually. See more info.

    $1.50
  • $1.50

    For use with Model C, D and E Indoor Rowers. These are the 1¼" diameter urethane pulleys that the chain runs over inside the indoor rower. There are two per machine: one is part of the traveling pulley (part number 1756); the other is mounted on a stationary axle and has two chain idler spacers (part number 1305) to keep it properly aligned. See more info.

    $1.50
  • $1.25

    This is part of the front monorail assembly. It is made of black plastic. For use on all Model C Indoor Rowers and on Model D Indoor Rowers manufactured from July 2003–2006.

    $1.25
  • $1.25

    For use on all Model C, D and E Indoor Rowers. This swivel bushing is installed at the swivel/handle end of the chain to prolong chain life and provide smoother rowing. See more info.

    $1.25
  • $1.25

    For use on the Model C, D and E Indoor Rower. This is the bumper for the rear of the monorail. See more info.

    $1.25
  • $1.00

    This is the acorn nut found on the top of the front bumper of the monorail. For use on all Model C Indoor Rowers and on Model D Indoor Rowers manufactured from July 2003–2006. Order two per machine. See more info.

    $1.00
  • $1.00

    For use with Model C and D Indoor Rowers and all SkiErgs Plastic cover for the bearing on the left side of the Model C or D Indoor Rower, opposite the flywheel, and the back side of all SkiErgs.

    $1.00
  • $0.95

    For use with Model C, D, E and Dynamic Indoor Rowers. This is the hardware for the 3-1/4 inch wide top seat rollers (two per machine). Includes one bolt, one nut, and two spacers. See more info.

    $0.95
  • $0.95

    This is the monitor bolt for the Model D and E Indoor Rower.

    $0.95
  • $0.90

    For use with Model C and original Model D Indoor Rowers. Replacement caster wheel located on the front foot of Model C and original Model D Indoor Rowers. Used when picking up the back end of the indoor rower and rolling it like a wheel barrow.

    $0.90
  • $0.85

    For use with Model C, D and E Indoor Rowers. This is the handle hook used on the Models C, D and E Indoor Rower. To store the handle long-term, place the handle up against the flywheel housing. For ease of use before or during a workout, placing the handle in the handle hook puts the handle within easy reach. Includes hardware.

    $0.85
  • $0.75

    This is part of the front monorail assembly. It is made of black plastic. For use on all Model C Indoor Rowers and on Model D Indoor Rowers manufactured from July 2003–2006.

    $0.75
  • $0.75

    For use with the handle on all models of indoor rowers. Connects the handle to the chain. The corresponding nuts are part number 240 for a Model A, B or C, and part number 1235 for Model D, E or Dynamic. See more info.

    $0.75
  • $0.70

    For use with all Model D and Model E Indoor Rowers. This part is found inside the foot bellies. Order two per foot belly. See more info.

    $0.70
  • $0.65

    For use on all Model C Indoor Rowers and on Model D Indoor Rowers manufactured from July 2003–2006.

    $0.65
  • $0.60

    This bolt attaches the monitor to the monitor arm. For use on all Model C Indoor Rowers and on Model D Indoor Rowers manufactured from July 2003–2006. See more info.

    $0.60
  • $0.55

    For use on the Model C, D and E Indoor Rower. To order the Handle Hook kit, which includes the two screws and nuts, order part number 1754.

    $0.55
  • $0.55

    For use with Model C, D, E and Dynamic Indoor Rowers. This is the hardware for the smaller bottom seat rollers (two per machine). Includes one bolt, one nut, one washer, and one spacer. See more info.

    $0.55
Showing 51 - 75 of 114 items