No products
Subcategories
For use with Model B Indoor Rowers only. 20" long pickup (sensor) and cable (wire) that transmit flywheel motion to the Performance Monitor on your indoor rower. If your monitor lights up with zeros but the display does not change when you begin rowing, you may need to replace this part. If the cable or cable housing is cut or broken you will definitely...
Water-resistant cover for the RowErg (with standard or tall legs) and Models A, B, C and D Indoor Rowers.
Intended for use with our Dynamic Indoor Rower, the Dynamic Link allows you to connect two or more Dynamic Indoor Rowers so you can train as a crew.
The Indoor Rower Floor Mat is made out of 3/16 inch (4.5 mm) thick black synthetic rubber (PVC) and measures 8.2 feet by 2.6 feet (250 cm by 80 cm). The mat can be used on any surface and helps protect the floor as well as eliminate slippage.
For use on all RowErgs with Tall Legs and BikeErgs. Includes caster wheels. See more info.
For use with the Model A and B Indoor Rower (Ergometer) only. This is the seat top and carriage only. Does not include hardware or seat rollers.
This is the handle drive cord for a Dynamic Indoor Rower. The handle drive cord is a single cord that is connected to the handle on one end and the foot carriage on the other end. Not for use on Model A, B, C, D, or E. See more info.
For use with Model A and B Indoor Rowers. Order this kit if you want to upgrade your Model A or B with the flexfeet standard on new indoor rowers. New flexfeet provide wider range of motion, greater security for the heel, easier adjustability to accommodate a wide range of foot sizes. See more info.
For use with light blue Model D Indoor Rowers manufactured from July 2003–July 2006. See more info.
For use with light blue Model D Indoor Rowers manufactured from July 2003–July 2006. See more info.
For use with Model D Indoor Rowers manufactured from July 2003–July 2006. Includes the most common wear and tear parts to keep your Model D in top condition. See more info.
For use with Model B Indoor Rowers only. Sprockets (gears) for the Model B flywheel axle. Includes both inner (15 tooth) and outer (13 tooth) sprockets. A new chain (part number 280) is also strongly recommended if you are replacing sprockets. The Flywheel Cog Tool Set (part number 484) is required to change sprockets and should be added to your order...
This is the original straight wooden handle that came with the Model A, B and C Indoor Rowers. It measures 16" long and can be used on all indoor rower models. Includes black rubber grips, handle U-bolt and two nuts. See more info.
For use with Model B Indoor Rowers. This 10ft long chain comes with a brass swivel at the handle end and chain connectors for the inside end. Fits Model B Indoor Rowers only. If your chain is badly rusted, has seized links or is broken, replace it with this part. See more info.
For use on all Model C Indoor Rowers and on Model D Indoor Rowers manufactured from July 2003–2006.
For use on all Model C Indoor Rowers and on Model D Indoor Rowers manufactured from July 2003–2006.
If you already own a Polar™ or Polar compatible heart rate chest belt transmitter and would like to enable the PM2/PM2+/PM3/PM4 heart rate monitoring function on your Concept2 Model A, B, C, D, or E Indoor Rower, this Concept2 Heart Rate Receiver is what you need.
This is the damper-side cover for the black Model D Indoor Rower. Does not include the four damper fan cover screws (order separately, part number 1276). See more info.
This is the metal part on the front top and front bottom of the monorail that makes contact with the hangar bolt tube on the front half of the indoor rower. For use on all Model C Indoor Rowers and on Model D Indoor Rowers manufactured from July 2003–2006. Order two per machine. See more info.
This is the damper-side cover for the gray Model D and Model E Indoor Rower. Does not include the four damper fan cover screws (order separately, part number 1276). See more info.
This is the damper-side cover for the light blue Model D Indoor Rower. Does not include the four damper fan cover screws (order separately, part number 1276). See more info.
For use with Model D and E Indoor Rowers. This is the generator base and coil that transmit flywheel motion to and generates power for the Performance Monitor on your indoor rower. See more info.
For use with Model A Indoor Rowers only. Chain is 10´ long and comes with the lap link for the inside end. Fits on Model A Indoor Rowers only. If your chain is badly rusted, has seized links, or is broken, you will need to replace it. See more info.